催化剂Ru/ZrO2-CeO2催化湿式氧化苯酚

催化剂Ru/ZrO₂-CeO₂催化湿式氧化苯酚的过程表明,Ru/ZrO₂-CeO₂可以显著提高COD和苯酚去除效果,当反应温度为170℃,压力为3 MPa,反应120 min后,COD和苯酚的去除率分别达到了99％和100％.试验还考察了不同反应条件对苯酚溶液COD去除的影响,并获得了最优的反应条件：温度为170℃,压力为3 MPa,催化剂的投加量为5　g/Ｌ,搅拌速度为500 r/min.通过对中间产物的分析,本研究提出了催化湿式氧化苯酚的简单路径图,认为苯酚首先被氧化成小分子有机酸,接着小分子有机酸被氧化成二氧化碳和水.前一个过程是快速反应,后一个过程中的乙酸氧化是慢速过程,需要在高温下才能完成.乙酸的氧化主要是自由基攻击α碳上的C—H键,先生成甲酸,并最终生成二氧化碳和水.     

Kinetics of selective catalytic reduction of NO by NH3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH3. The kinetics of the SCR reaction in the presence of O2 was studied in this work. The results show that the observed reaction orders were 0.74-0.99, 0.01-0.13, and 0 for NO, O2 and NH3, respectively, at 350-450℃. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst. The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N2 and H2O. Gaseous O2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process. It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH3.     

Pd/C气体扩散电极用于电生成H2O2降解苯酚的研究

采用自制的Pd/C气体扩散阴极和Ti/IrO2/RuO2阳极,在无隔膜电解槽中对苯酚模拟废水降解效果及机制进行了研究,采用电子自旋共振法(ESR)对电解体系中产生的羟自由基(·OH)进行了检测.结果表明,在Pd/C气体扩散体系中掺杂Pd催化剂可以促进H2 O2的生成(H2 O2的稳定浓度是7.5 mg/L),有利于·OH的产生.经电化学氧化处理120 min后,苯酚和COD的去除率分别达到97.2%和50%,表明在电催化氧化过程中苯酚被氧化生成了大量低分子量中间产物.废水的BOD5/COD值达到0.73是处理前的9.1倍,苯酚废水的可生化降解性通过电化学氧化处理后显著提高.在该电化学体系中苯酚的降解是在阳极直接、间接氧化及阴极产生的H2 O2、·OH的氧化共同作用下完成的.通过对紫外扫描光谱图的分析推断出苯酚在电解过程中有醌类物质生成;由GC-MS检测到了邻苯二酚、对苯二酚、苯醌等芳香族化合物和己二酸、顺丁烯二酸、反丁烯二酸、丁二酸、丙二酸、乙二酸等短链羧酸,据此提出了苯酚降解的可能历程.     

利用泰乐菌素菌渣生产复合酶制剂及效果研究

发酵法生产抗生素过程中会产生大量废弃菌渣,这些菌渣因有机质含量高,堆放极易发生霉变,给当地环境造成危害.文章采用固体发酵法,以微生物降解处理后的泰乐菌素菌渣为主要原料,生产复合酶制剂,并对其在肉鸡上的使用效果进行研究.结果表明:在水含量50％～60％、干物质中麸皮含量不低于40％的泰乐菌素菌渣培养基中,接入5％～10％...     

Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines

This study investigated the filtration and continuous regeneration of a particulate filter system on an engine test bench, consisting of a diesel oxidation catalyst（DOC） and a catalyzed diesel particulate filter（CDPF）. Both the DOC and the CDPF led to a high conversion of NO to NO2 for continuous regeneration. The filtration efficiency on solid particle number（SPN） was close to100%. The post-CDPF particles were mainly in accumulation mode. The downstream SPN was sensitively influenced by the variation of the soot loading. This phenomenon provides a method for determining the balance point temperature by measuring the trend of SPN concentration.     

Unregulated emissions from diesel engine with particulate filter using Fe-based fuel borne catalyst

The alteration and formation of toxic compounds and potential changes in the toxicity of emissions when using after-treatment technologies have gained wide attention. Volatile organic compound（VOC）, carbonyl compound and particle-phase polycyclic aromatic hydrocarbon（PAH） emissions were tested at European Steady State Cycle（ESC） to study unregulated emissions from a diesel engine with a fuel-borne catalyst and diesel particulate filter（FBC–DPF）. An Fe-based fuel-borne catalyst was used for this study. According to the results, brake specific emissions of total VOCs without and with DPF were 4.7 and4.9 mg/kWh, respectively, showing a 4.3% increase. Benzene and n-undecane emissions increased and toluene emission decreased, while other individual VOC emissions basically had no change. When retrofitted with the FBC–DPF, total carbonyl compound emission decreased 15.7%, from 25.8 to 21.8 mg/kWh. The two highest carbonyls, formaldehyde and acetaldehyde, were reduced from 20.0 and 3.7 to 16.5 and 3.3 mg/kWh respectively. The specific reactivity（SR） with DPF was reduced from 6.68 to 6.64 mg/kWh. Total particle-phase PAH emissions decreased 66.4% with DPF compared to that without DPF. However, the Benzo[a]pyrene equivalent（BaPeq） with DPF had increased from 0.016 to 0.030 mg/kWh.Fluoranthene and Pyrene had the greatest decrease, 91.1% and 88.4% respectively. The increase of two- and three-ring PAHs with DPF indicates that the fuel-borne catalyst caused some gas-phase PAHs to adsorb on particles. The results of this study expand the knowledge of the effects of using a particulate filter and a Fe-based fuel-borne catalyst on diesel engine unregulated emissions.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Review of the progress in preparing nano Ti02： An important environmental engineering material

TiO2 nanomaterial is promising with its high potential and outstanding performance in photocatalytic environmental applications, such as CO2 conversion, water treatment, and air quality control. For many of these applications, the particle size, crystal structure and phase, porosity, and surface area influence the activity of TiO2 dramatically. TiO2 nanomaterials with special structures and morphologies, such as nanospheres, nanowires, nanotubes, nanorods, and nanoflowers are thus synthesized due to their desired characteristics. With an emphasis on the different morphologies of TiO2 and the influence factors in the synthesis, this review summarizes fourteen TiO2 preparation methods, such as the sol-gel method, solvothermal method, and reverse micelle method. The TiO2 formation mechanisms, the advantages and disadvantages of the preparation methods, and the photocatalytic environmental application examples are proposed as well.     

V2O5/TiO2催化剂脱除NO的研究

采用了等体积浸渍法制备二氧化钛负载钒氧化物催化剂（V2O5/TiO2）,研究了V2O5负载量、反应温度、烟气流量、氨氮比以及运行时间各因素对NH3选择性催化还原NO反应（SCR）效率的影响.研究结果表明：经过500℃温度下煅烧,烟气流量为200ml/min,负载量为7wt％的V2O5/TiO2催化剂,在400℃温度下反应,NO脱除率可达70.5％.     

氟化铵制备氟化钙最优条件研究

试验采用氟化铵与石灰石粉、石灰乳反应制取氟化钙,研究了反应温度、物料浓度、物料过量系数等各主要参数变化对氟化钙结晶、过滤速度、氟收率及其含量的影响,摸索出最优反应条件。